Engines - Dyno Tuned
- Accessories
- Alternators/Kits/Parts
- AN Fittings/Hose/Tools
- Barrel Shims
- Bearings/Parts
- Brake Kits
- Brake Parts
- Breather Boxes
- Camshafts
- Camshaft Gears
- Camshaft Kits
- Camshaft Lifters
- Camshaft Parts
- Carb Air Cleaners/Parts
- Carb Gaskets
- Carb Kits/Singles
- Carb Manifolds/Linkages
- Carb Parts/Tools/Jets
- Carb Pumps/Regs/Fittings
- Carb Rebuild Kits
- Cars For Sale
- Cases/Install Kits/Parts
- Connecting Rods/Bolts
- Cooling Systems
- Crankshafts/Parts
- Engines - Built to Order
- Engines - DIY Kits
- Engines - For Sale
- Engines - Rebuild Kits
- Exhausts/Parts
- Exhausts - OffRoad/Trike
- Flywheels/Parts
- Gaskets/Seals
- Gauges
- Heads/Spark Plugs
- Head Stud Kits
- Ignition/Kits/Parts
- Oil Pumps/Filters/Parts
- Pistons/Cylinder Kits
- Piston Rings
- Pulleys/Kits/Parts
- Race Car Products
- Services/Machining
- Shifters
- Starter Motors/Parts
- Suspension/Parts
- Tinware/Kits/Parts
- Transmissions/Parts
- Used Parts
- Valve Train/Parts
- Wheels
- Wheel Studs, Nuts & Bolts
- Workshop Tools
- Xtra Helpful Information
Featured Posts
- RPR TurnKey Dyno'd Engine Installation and Service procedures
- Luke's Signature Turnkey 2276cc engine
- Hotmail.com, Live.com and Outlook.com email problems
- Type 1, Type 2, Type 3 ????
- Shanti's Signature Turnkey 2276cc engine
- Liz's Signature Turnkey 2276cc engine
- Christian's Signature 2054cc Engine
- Ray's 1916cc Karmann Ghia Engine
- Jason's 2276cc Race Engine
RPR Ready Built Engines - 1916cc Long Block
RPR-11775
New
NLA , Currently not in Stock or Special Order - Please Contact Us
More info 6771 page views!
RPR Ready Built Engines - 1916cc Long Block
This completely 100% new engine is 1916cc and ready to install into any Type 1 Beetle, Buggy or Kit car.
This engine should make around around 129 HP at the wheels.
These are the specifications:
| Magnesium Case - AS41 Brazilian Case - 94mm bore |
| Crankshaft - 69mm - 4140 - VW Journal |
| Flywheel - Type 1 - VW 200mm VW Lightweight Forged Cromoly Flywheel 12V |
| Gland Nut - 36mm Washer included - for Type 1 crank |
| I-Beam Connecting Rod Set - Type 1 - VW Journal - 5.400" - set of 4 |
| Main Bearing - Type 1 - 600 Standard Case - Standard Crank |
| Dowel Pin Set (5) - Replace your old or lost bearing dowels |
| Conrod Bearing - Type 1 - Standard Size |
| Camshaft Bearing - Type 1 - Dual Thrust |
| EMPI - Cam Plug (Steel) 1600cc and up engine cases |
| Engle W Series - W110 Cam |
| Engle - Cam Gear |
| Engle - Cam Gear Bolts |
| Degree pulley - 7" - Black numbers |
| Extra long crank pulley bolt and washer - used with Bolt on Sand seals |
| Engle - Lifter Set |
| SCAT crank install kits - does not include the distributor drive shaft |
| New case install kit - Slotted relief plugs - Dual Port Engines |
| New case nut bolt kit (100+ pieces) |
| Oil pressure Switch (Stock replacement Sender) |
| CB Performance 26mm Full Flow IN/OUT oil pump - Suits all flat and all aftermarket camshafts |
| Gasket Kit for 1300 - 1600 engine - includes rear main seal (Elring) |
| 94 x 69 - 1915cc Piston & Cylinder Kit - machining is required |
| Lower Cylinder Deflector Tins in gloss black paint - (per pair) |
| Los Panchito Heads - (40 x 35.5) 94mm |
| Opening Heads for Larger Bore Size (per pair) |
| Lash Caps per set of 8 - steel caps fit on the end of valves |
| AA 1.25 Ratio Rockers Kit |
| Distributor drive pinion (VW) - includes shims and anti chatter spring |
| Stainless Valve Cover (with internal tabs) - for performance engines - (set of 2) |
| JayCee Leak proof push rod tubes - Blue |
| Flywheel Shims - used to take up the excessive gap - .024mm (per shim) |
| 8mm - Cromoly head stud kit (SCAT) - includes all nuts and washers |
| Push Rods - Aluminum Super Duty Push Rods - Cut to Length (set of 8) |
| SCAT billet sump plate kit (plate, gaskets, washer and Acorn nuts) |
| Chrome Dipstick |
| Oil Strainer |
| Engine Assembly (Stage 1) - using RPR Supplied parts and products |
Please contact me for a complete specification sheet on this engine that is ready to install today!